Search results

Well got the unit apart ( worst thing was the glue) and adjusted it so i had a sharp view in the daylight ( was going to check it when it was dark and readjust as required) Then the live view froze. The time was still running but the live view just didn't change. Rebooted the unit and then come...

Many thanks for this and all your input Paul

have just tried playback through the NVR, IVMS and the HIK-connect all show the same. 100% viewing through the main stream just really blurry. So restored the unit to factory defaults and then re-entered the info JB1970 and then reviewed again but its still the same. So does anybody have the...

The NVR has allocated the ip address for the cameras so I would not be able to “ping” the ip addresses as they would be blocked by the NVR’s ip address. I did try to ping the cameras using JG1970 instructions (http://NVR_IP_Address:650xx (where xx is the channel number for the camera - IE...

can you ping it from the NVR ?? For some strange reason I have remote access through the NVR web interface but not directly so I’m unable to ping the camera direct ( have tried and failed ) with regard the the corrosion plug and socket are fine checked this and all good

Will have a look when I get home thanks again for all your help

It’s very strange I did put the bitrate to constant instead of variable and the stream info went up to 7/8Mbps so the cameras seeing the changes. Regarding the reset of the camera can you just hold the rest button behind the sd card holder, or is there a software what would wipe and reset it...

when that stream was only doing 2Mbps I went to another camera as I have set it the same as the blurry one and that stream info is ranging from 2Mbps up to 7Mbps and it’s the same camera. Could it be that it could be the camera at fault?? As I said it was fine and now it’s not

When I try to log in to the camera using http:/ with my details it says unable to connect. So when I log in through the NVR’s IP address I have system config , then network config then under that I have network parameter, hik connect , platform access and network service. I don’t have anything...

Again thank for all your input. I have looked at the info when looking at the camera and it’s showing correct. Encoding H265 , frame rate 12fps bite rate between 855kbs and 2Mbps, stream type main stream and resolution is 3840 x 2160. So it seems the camera is the problem. Does anybody have the...

Yes it is a 8Mp but I tried it at 4Mp in case. I have tried both the video setting ( greatly appreciated)!!! But still blurry :( also checked the recording schedule and yes set to record main stream. As I said I didn’t have a problem with it when I first put them back up from having the house...

Attached camera setting a

I thought it was a setting problem but it was ok with the current setting when first put in. So I copied the settings from another camera (have two cameras the same ) and makes no difference. I will pop the settings on later in case I done something stupid

It’s blurry and really not as crisp as it was. The camera is about 7 years old so it’s done its work. Just seems I’ve been having a few problems with the setup over the last couple of years. Had a knock on the door from my next door neighbour that some lowlife at 3:45 was trying his front door...

Sorry no UK

Just a bit of an update after trying all of the above I removed one camera as was having problems with a blurry image so decided to use that one as the test. Plugged into the computer and used the SADP tool to confirm the IP address. I couldn’t log in through the ip address even after a reset...

Ok i have downloaded Chrome and Firefox and gone through the steps as above and still says 'upgrading failed' Is there anyway i can upgrade through the NVR direct?

The NVR is DS7608NI-M2 running v05.03.010 build 240606 yes the cameras are connected to the NVR direct no haven’t tried using browser could try that .

Just to make sure I'm doing it right gone through my web browser (edge) then to device, video device. the right hand column. I then get a warning message saying 'The connected device firmware is incompatible, which may affect the rule configuration. It is recommended to upgrade the connected...

nope says update failed :(