Recent content by scottda

Hi @Dan Thanks for the reply. I feared as much but that’s so annoying as it’s a great feature and the NVR is hardly archaic in age

I have a DS-7616NI-I2 / 16P NVR with 2387 Gen 2 cams, just cant get this colour coding to work on my NVR when in Hikvision playback. Have set up another 2 NVRs with the same cams and they work fine with the colour coding in the hikvision playback, one is a K series and one is an M series. Is...

Thanks for the response, but have now confused myself. I set the recording schedule on the cams themselves via a direct web connection. I set them to continuous. Are you saying that this only applies to any local storage (i.e. to an SD card) and that any schedule set on the NVR what controls...

sorry, old thread but how do you configure doing this. i.e. is it just as simple as setting up the SD card in the storage management section of the camera and will it overwrite as needed? And assuming you have it set to notify surveillance centre its going to record to the NVR as well?

Hi all Have two ANPR IDS-2CD7A26G0/P-IZHSY cameras set up doing ANPR validation to control entry/exit on a gate system. All working beautifully, well nearly!!!!. During the day, everything is fine, but at night some cars are not being detected and hence number plates not being read. Its...

Hi all, installed a new Hikvision CCTV solution and all working fine. Replacing the intercom now that controls a FAAC 455 gate control board. The FAAC control board only works with clean contact zero voltage triggers. Can anyone advise if the KD8003 is zero voltage on the NO terminals? thanks

thanks for the heads up, yes i was thinking the same. Was thinking maybe using the alarm out on the NVR to do this. Not sure about closing the gates, probably just need to have them on a timed close after opening. thanks

Hi all, sorry i know this is an older thread but will be doing something similar, adding a Hikvision intercom to an existing FAAC gate opener panel. I have just installed a full hikvision CCTV setup to this property, a question i have is whether its possible to do an automated opening via ANPR...

Thanks. I am viewing the cameras remotely through a browser. When I bring up a camera in full screen it maintains the 720 image and does not use the main stream. I can’t use local monitor due to placement of the NVR. I have seen screenshots of enabling third stream in the NVR (seems to suggest...

Hi all, does anyone know if the Hikvison DS-7616NI-I2 / 16P supports third stream. I cant live view my 5 cams at 4k as it exceeds transcoding limit, i have substream set to 720p at the moment. I would like to view them at 1920x1080 and have enabled third stream on my cameras but I cant find...

I cant believe I did this..I tried so many times with so many combinations and it always said offline. I put them back to defaults to take the picture snip and just noticed the status was greyed out so probably assumed it was still offline, was expecting it to go bold like the rest of the...

Hi all, sorry I know this is a pretty common question but I have read all the posts yet still cant find a solution. I have a new DS-7616NI-I2/16P NVR and 5 8MP Colorvu cams. Have it all set up (of sorts) still tinkering with settings etc. However unable to get the Hik-Connect online at all on...

great, thank you!

Hi Dan, sorry one more question....I heard the NXI have a much nicer and newer interface, is this correct. If so and I decided to go with the NXI instead of the NI, would the accusense on the camera override the NVR or would there be a compatibility issue at all?

Thanks for the super quick reply Dan, its very much appreciated. OK so looks like i will go with that recommendation on the NVR then and get the 12 channel with 5 cams and leverage the accusense via the cams themselves. thanks again.